WHY Test Flexural Strength?

Designers of pavements use a theory based on flexural strength. Therefore, laboratory mix design based on flexural strength tests may be required, or a cementitious material content may be selected from past experience to obtain the needed design MR. Some also use MR for field control and acceptance of pavements. Very few use flexural testing for structural concrete. Agencies not using flexural strength for field control generally find the use of compressive strength convenient and reliable to judge the quality of the concrete as delivered.

How to Use Flexural Strength?

Beam specimens must be properly made in the field. Pavement concrete mixtures are stiff (1/2 to 21/2-inch slump). Consolidate by vibration in accordance with ASTM C 31 and tap sides to release air pockets. For higher slump, after rodding, tap the molds to release air pockets and spade along the sides to consolidate. Never allow the beam surfaces to dry at any time. Immerse in saturated limewater for at least 20 hours before testing.

Specifications and investigation of apparent low strengths should take into account the higher variability of flexural strength results. Standard deviation for concrete flexural strengths up to 800 psi (5.5 MPa) for projects with good control range from about 40 to 80 psi (0.3 to 0.6 MPa). Standard deviation values over 100 psi (0.7 MPa) may indicate testing problems. There is a high likelihood that testing problems, or moisture differences within a beam caused from premature drying, will cause low strength. Where a correlation between flexural and compressive strength has been established in the laboratory, core strengths by ASTM C 42 can be used for compressive strength to check against the desired value using the ACI 318 criteria of 85 percent of specified strength for the average of three cores. It is impractical to saw beams from a slab for flexural testing. Sawing beams will greatly reduce measured flexural strength and should not be done. In some instances, splitting tensile strength of cores by ASTM C 496 is used, but experience is limited on how to apply the data.

Another procedure for in-place strength investigation uses compressive strength of cores calibrated by comparison with acceptable placements in proximity to the concrete in question:

What are the Problems with Flexure?

Flexural tests are extremely sensitive to specimen preparation, handling, and curing procedure. Beams are very heavy and can be damaged when handled and transported from the jobsite to the lab. Allowing a beam to dry will yield lower strengths. Beams must be cured in a standard manner, and tested while wet. Meeting all these requirements on a jobsite is extremely difficult often resulting in unreliable and generally low MR values. A short period of drying can produce a sharp drop in flexural strength.
Many state highway agencies have used flexural strength but are now changing to compressive strength or maturity concepts for job control and quality assurance of concrete paving. Cylinder compressive strengths are also The data point to a need for a review of current testing procedures. They suggest also that, while the flexural strength test is a useful tool in research and in laboratory evaluation of concrete ingredients and proportions, it is too sensitive to testing variations to be usable as a basis for the acceptance or rejection of concrete in the field.
Related Pages

• Concrete Slab
• How to remove stains from Concrete
• Concrete Technology Lecture Notes
• Concrete Technology Questions Answers

References

1. How Should Strength be Measured for Concrete Paving? Richard C.Meininger, NRMCA TIL 420, and Data Summary, NRMCA TIL 451, NRMCA, Silver Spring, MD.
2. Concrete Strength Testing, Peggy Carrasquillo, Chapter 14, ASTM STP 169C, Significance of Tests and Properties of Concrete and Concrete-Making Materials, American Society for Testing and Mater-ials, West Conshohocken, PA.
3. Related Articles to this Article

   

   Neelum Jhelum Hydropower Project: An Engineering Marvel

   Energy and water are the prime movers of human life, though deficient in oil and gas, Pakistan has

   

   Quasi Static Test

   The quasi-static cyclic tests can be used to conduct both basic and proof tests. In quasi-static te

   

   Shock Table Dynamic Test

   In the absence of a shaking table, some laboratories have developed simple simulators for dynamic t

   

   Pseudo Dynamic (PsD) Tests

   The concept of pseudo-dynamic test (also called computer-actuator on-line test or hybrid test) was

   

   Failure Modes of Masonry Structures

   Vibrations caused by earthquakes generate additional loading. Shear stresses develop which cause dam

   Read more similar Articles
   Tags:

   • Concrete

   ← Estimation of Reinforced Concrete RCC Water Tank		Ground Water Occurrence & Types of Ground Water →

   < Previous		Next >