EnggPedia - The Engineering Encyclopedia

Sat11222014

Last update06:04:15 AM

Font Size

Profile

Menu Style

Cpanel
Back Chemical Chemical Engineering Dictionary Chemical Processes Sulphonation - Sulfonation - Definition, Uses & Its Application

Sulphonation - Sulfonation - Definition, Uses & Its Application

Sulphonation is the introduction of a sulfonic acid group (–SO3H) into an organic compound as, for example, in the production of an aromatic sulfonic acid from the corresponding aromatic hydrocarbon.

The usual sulfonating agent is concentrated sulfuric acid, but sulfur trioxide, chlorosulfonic acid, metallic sulfates, and sulfamic acid are also occasionally used. However, because of the nature and properties of sulfuric acid, it is desirable to use it for nucleophilic substitution wherever possible.

ArH + H2SO4 → ArSO3H + H2O

alt

alt

For each substance being sulfonated, there is a critical concentration of acid below which sulfonation ceases. The removal of the water formed in the reaction is therefore essential. The use of a very large excess of acid, while expensive, can maintain an essentially constant concentration as the reaction progresses. It is not easy to volatilize water from concentrated solutions of sulfuric acid, but azeotropic distillation can sometimes help.

The sulfonation reaction is exothermic, but not highly corrosive, so sulfonation can be conducted in steel, stainless-steel, or cast-iron sulfonators. A jacket heated with hot oil or steam can serve to heat the contents sufficiently to get the reaction started, then carry away the heat of reaction.

A good agitator, a condenser, and a fume control system are usually also provided. 1- and 2-naphthalenesulfonic acids are formed simultaneously when naphthalene is sulfonated with concentrated sulfuric acid. The isomers must be separated if pure α- or β-naphthol are to be prepared from the product mix. Variations in time, temperature, sulfuric acid concentration, and acid/hydrocarbon ratio alter the yields to favor one particular isomer, but a pure single substance is never formed. Using similar acid/hydrocarbon ratios, sulfonation at 40oC yields 96% alpha isomer, 4% beta, while at 1600C the proportions are 15% α-naphthol, 8.5% β-naphthol.

The a-sulfonic acid can be hydrolyzed to naphthalene by passing steam at 160oC into the sulfonation mass. The naphthalene so formed passes out with the steam and can be recovered. The pure b-sulfonic acid left behind can be hydrolyzed by caustic fusion to yield relatively pure b- naphthol. In general, separations are based on some of the following consideration:

  1. Variations in the rate of hydrolysis of two isomers
  2. Variations in the solubility of various salts in water
  3. Differences in solubility in solvents other than water
  4. Differences in solubility accentuated by common-ion effect (salt additions)
  5. Differences in properties of derivatives
  6. Differences based on molecular size, such as using molecular sieves or absorption.

Sulfonation reactions may be carried out in batch reactors or in continuous reactors. Continuous sulfonation reactions are feasible only when the organic compounds possess certain chemical and physical properties, and are practical in only a relatively few industrial processes. Most commercial sulfonation reactions are batch operations. Continuous operations are feasible and practical (1) where the organic compound (benzene or naphthalene) can be volatilized, (2) when reaction

rates are high (as in the chloro-sulfonation of paraffins and the sulfonation of alcohols), and (3) where production is large (as in the manufacture of detergents, such as alkylaryl sulfonates). Water of reaction forms during most sulfonation reactions, and unless a method is devised to prevent excessive dilution because of water formed during the reaction, the rate of sulfonation will be reduced. In the interests of economy in sulfuric acid consumption, it is advantageous to remove or chemically combine this water of reaction. For example, the use of reduced pressure for removing the water of reaction has some technical advantages in the sulfonation of phenol and of benzene.

The use of the partial-pressure distillation is predicated upon the ability of the diluent, or an excess of volatile reactant, to remove the water of reaction as it is formed and, hence, to maintain a high concentration of sulfuric acid. If this concentration is maintained, the necessity for using excess sulfuric acid is eliminated, since its only function is to maintain the acid concentration above the desired value.

Azeotropic removal of the water of reaction in the sulfonation of benzene can be achieved by using an excess of vaporized benzene. The use of oleum (H2SO4.SO3) for maintaining the necessary sulfur trioxide concentration of a sulfonation mixture is a practical procedure.

Preferably the oleum and organic compound should be added gradually and concurrently to a large volume of cycle acid so as to take up the water as rapidly as it is formed by the reaction. Sulfur trioxide may be added intermittently to the sulfonation reactor to maintain the sulfur trioxide concentration above the value for the desired degree of sulfonation.

Related Articles to this Article
The osmotic pressure is  a pressure that must be  applied to a more concentrated solution to brin
All plastics are polymers mostly containing carbon and hydrogen and few other elements like chlorin
Gasification process consists of two parts, a liquefaction step and an entrained bed gasifier. In t
A catalyst is a substance that, without itself undergoing any permanent chemical change, increases
Refrigeration systems are common in the natural gas processing industry and processes related to th
Read more similar Articles

Enggpedia's Site Map

Chemical Engg.

  1. Thermodynamics
  2. In Organic Chemistry
  3. Analytical Chemistry
  4. Organic Synthesis

Civil Engg.

  1. Structural Engg.
  2. Building Construction
  3. Environmental Engg.

Mechanical Engg.

  1. Thermodynamics
  2. Strength of Materials
  3. Machines
  4. Engines & Turbines

Electrical Engg.

  1. Electronics
  2. Digital Logic Design
  3. Programming

Industrial Engg.

  1. Industries
  2. Machines
  3. Management
  4. Cost & Estimation

Basic Sciences

  1. Calculus
  2. Differential Equations
  3. Fluid Mechanics